Untitled Document
 
 
 
Instructions
  1. Click Menu > System Settings > Sip Proxy > Default.
  2. Display Name : (your name)
  3. Username : (your XTCiP sip account) *provide by XTCiP
  4. Password : (your XTCiP sip password) *provide by XTCiP
  5. Domain/Realm : xtc.xtcip.com
  6. Sip Proxy : xtc.xtcip.com
  7. Out Bound Proxy : xtc.xtcip.com
  8. After you finish Key in this infomation Click Back (3x) > Click Close.
  9. You can see logged in - Enter Phone Number ( Your Number is XXXX ) that mean your ready to make a call.
  10. Enjoy !!!
 
 
Instructions
  1. Right Click on the screen > Click Setting.
  2. Display Name : (your name)
  3. Username : (your XTCiP sip account) *provide by XTCiP
  4. Password : (your XTCiP sip password) *provide by XTCiP
  5. Domain : xtc.xtcip.com
  6. After you finish Key in this infomation Click Apply > Click Ok.
  7. You can see logged in - Enter Phone Number ( Your Number is XXXX ) that mean your ready to make a call.
  8. Enjoy !!!
 
 
Instructions
 
Reset To Factory Default Setting
  1. Pic up the phone attached to your Linksys PAP2.
  2. Dial ****73738#
  3. Press 1 to confirm.
  4. Hang up the phone.
Set To DHCP Mode
Step A , Set to DHCP
  1. Pic up the phone connected to the "Phone 1" port of the Linksys PAP2 and anter ****. You will then hear a voice say, "Configuration menu".
  2. Press the keys 1 1 0# on your analog phone.
  3. Press 1 # to enable DHCP.
  4. Press 1 to save your configuration setting. Hang up the phone and wait for a couple minutes.
Step B , Verify Linksys PAP2 has a vali IP address.
  1. Pic up the phone connected to the "Phone 1" port of the Linksys PAP2 and anter ****. You will then hear a voice say, "Configuration menu".
  2. Press keys 1 1 0 # on your analog phone. The system will then read back the IP address of your Linksys PAP2.Please write this down.
 
Set to static IP
The Linksys PAP2 adaptor you have recived for your Broadband Phone Service is fully configured, and within minutes you can begin to make your calls. Members using Static IP on their home or office network may wish to configure the adaptor with Static IP. If you have obtained a Static IP with internet service provider (ISP) and wish to configure your adaptor with Static IP settings, please follow as a below:
  1. You will first have to obtain the following infomation : IP Address, Default Gateway and Subnet Mask. If you are using a router, please contact the router manufacturer fo instructions for retrieving this infomation from the router directly. If you have obtained a Static IP from your internet provider (ISP) and wish to configure your adaptor with your static IP settings, please obtain the infomation directly from your ISP.
  2. Pick up the telephone receiver of the phone connected to the adaptor and dial ****. You will hear a voice prompt say "Configuration menu"
  3. Press the keys 1 0 1 # on your analog phone to access the static IP configuration menu.
  4. Press 0 # to disable DHCP, then press 1 to save setting.
  5. Press 1 1 1 # to access the IP address Menu.
  6. Enter your IP address followed by # (i.e.,"192*168*0*10 #" to represent the IP 192.168.0.10). Press 1 to save the setting.
  7. Press 1 2 1 # to access the subnet mask menu.
  8. Enter your Subnet Mask (i.e., "255.255.255.0 #" to represent the subnet mask 255.255.255.0). Press 1 to save the setting
  9. Press 1 3 1 # to access the Default Gateway Menu.
  10. Enter your Default Gateway followed by # (i.e.,"192*168*0*1 #" to represent the Gateway 192.168.0.1). Press 1 to save the setting. Hang up.
  11. Pic up the phone connected to the "Phone 1" port of the Linksys PAP2 and anter "****". You will then hear a voice say, "Configuration menu".
  12. Press keys 1 1 0 # on your analog phone. The system will then read back the IP address of your Linksys PAP2.Please write this down.
 
Web Base Configuration
  1. Open Internet explorer
  2. Key in add address bar your linksys PAP2 ip address
  3. Click add Admin login > Line 1
  4. Display Name : (your name)
  5. User ID: (your XTCiP sip account) *provide by XTCiP
  6. Password : (your XTCiP sip password) *provide by XTCiP
  7. Proxy : xtc.xtcip.com
  8. Preferred Codec: G723
  9. After you finish Key in this infomation Click Save Setting Page will redirect to Info
  10. You can see at info all infomations. Please check at Registration State : Online. That mean your ready to make a call.
  11. Enjoy !!!
  12. If Registration Stat : Can't Connect to server. that mean u need to check all configuration and make sure your Linksys PAP2 can connect to internet.
  13. For future infomation and support please contact our technical support at 03 7261 4000 or email to support.xtcip.com.
 
 
 
 
 
Untitled Document
 
Copyright © XTC Solution 2005-2006 | All rights reserved